Products

Impact-rated safety glasses and goggles for cutting, drilling and demolition.Styles in stock: Clear Safety Glasses · Clear Hornet Safety Glasses · ...

SDS-Plus rotary hammer bits for fast drilling in concrete, for anchors and Tapcons.Sizes in stock: 5/32" x 6" · 1/4" x 6" · 3/8" x 6"Call (904) 764...

The SDWC Truss screw provides a stud-to-bottom plate or stud-to-top plate connection as well as fastening trusses and rafters to top plates. The fu...

A34 and A35 framing angles — inexpensive, all-purpose connectors for blocking, joists, rafters and plates. A35: multi-purpose framing anchor, bend ...

Simpson ABU and ABW post bases anchor 4x4, 4x6 and 6x6 posts to concrete and hold the post off the slab to prevent rot. 1" standoff keeps the post ...

Simpson bearing plate washers for anchor bolts at sill plates — square LBPS and round LBP in 1/2" and 5/8". 3" square LBPS for code-required sill p...

The popular H2.5A hurricane tie in stainless steel for coastal homes, docks and pool enclosures. Stainless steel for severe corrosion exposure Same...

HCP hip corner plates tie hip rafters or hip trusses to the double top plate at building corners. Hip-to-plate connection at outside corners Resist...

Twist straps make a 90° transition to tie trusses and rafters to studs or beams for uplift resistance. Pre-twisted 90° for truss/rafter-to-stud con...

HU heavy-duty face-mount hangers for beams, built-up headers and 4x members. Heavy-gauge steel for beam-to-beam and header connections Sizes for do...

Concealed-flange hangers keep the flanges hidden inside the joist — ideal at the end of a header or beam, or anywhere a clean look matters. Flanges...

Simpson H-series hurricane ties connect rafters and trusses to the wall plate to resist wind uplift — required on virtually every Florida roof. Raf...

HUS hangers are a heavier-gauge, double-shear face-mount hanger for higher joist loads in decks, floors and headers. Heavier 14- and 16-gauge steel...

LRU hangers support rafters at a slope (up to 45°) at ridges and headers without bevel cuts. Field-adjustable slope for rafter connections Installs...

LS skewable angles bend to any angle on site for skewed joist, rafter and blocking connections. Field-skewable to fit odd angles Lengths LS30 throu...

Stainless steel LUS face-mount joist hangers for docks, pools and waterfront decks where even ZMAX galvanizing will not hold up. Type 316 stainless...

The LUS is Simpson's most popular face-mount joist hanger — double-shear nailing gives high loads with fewer nails. Single, double and triple sizes...

Flat strap ties for continuous load paths — tie studs to plates, floors to floors and headers to framing. Lengths from 12" to 36" For wall-to-floor...

Post caps connect beams to the tops of posts for decks, porches, pergolas and carports. AC & LCE: adjustable post caps and column caps BC: 4x4,...

Simpson adhesive anchoring and retrofit bolts for setting rebar, threaded rod and anchor bolts into existing concrete. SET-PAC10 and ET22 high-stre...

Field-adjustable hangers for skewed and sloped joist and rafter connections — set the angle on the job instead of special-ordering. LSU/LSSU: field...

Specialty Simpson connectors for gusset, stair stringer, purlin and kneewall connections. HGA10: gusset angle for truss and rafter-to-plate LSC: ad...

Simpson Strong-Tie Strong-Drive SD connector screws, the rated fastener for joist hangers, straps and hurricane ties.In stock at Durham: SD9212SS #...

Simpson Strong-Tie Strong-Drive SDS heavy-duty connector screws, a code-listed alternative to lag screws for connectors and wood-to-wood connection...